February AIContract Templates

New Zealand · Business & partnerships

Contract Manufacturing Agreement
Contract Template for New Zealand

New Zealand customer-controlled contract manufacturing programme with process validation, lot release, statutory safeguards, recall and workplace coordination.

Governing law: New ZealandPublished templateUpdated 2026-10-01
CONTRACT MANUFACTURING AGREEMENT
CONTRACT MANUFACTURING AGREEMENT New Zealand Date: [date]. Customer: [legal name, New Zealand company or business number and address] (Customer). Contract Manufacturer: [legal name, New Zealand company or business number and address] (Manufacturer). Product means each finished product in Schedule 1. Product Dossier means its Customer-controlled specifications, materials, approved sources, packaging, tests and release criteria. Production Order means an order accepted under clause 3. Lot means Product made under one production record. Customer Property means the items in Schedule 3. Nonconformity means failure to meet the Product Dossier, an accepted Production Order or a mandatory requirement allocated to the Manufacturer. Working Day excludes Saturdays, Sundays and public holidays at the delivery location. 1. Contract-manufacturing programme The Customer appoints the Manufacturer to establish the agreed production process and manufacture Product for the Customer. The appointment is [non-exclusive/exclusive only as defined in Schedule 1]. The Manufacturer must use reasonable care and skill, trained personnel, fit facilities and documented quality controls. The Manufacturer may manufacture Product only for the Customer and only against an accepted Production Order. It must not change the Product Dossier, site, critical equipment, source, material or material process without prior written approval. Approval does not relieve it of responsibility for its performance. 2. Transfer, validation and release Before routine production, the parties must complete the transfer and validation plan in Schedule 1. The Manufacturer must document trial Lots, parameters, test-method suitability, deviations and agreed acceptance results. Commercial manufacture starts only after both parties approve the validation record. The Manufacturer must keep each Lot record and provide the specified certificates, samples and test results. Its authorised quality representative may release a Lot only after confirming conformity. Customer review does not waive a latent Nonconformity. 3. Forecasts and Production Orders A forecast is for capacity planning and is not a commitment unless Schedule 2 states a minimum. A Production Order must identify Product, quantity, NZD price, delivery date and destination. It becomes binding only when accepted in writing within [five] Working Days. Silence is not acceptance. This agreement prevails over a Production Order except for permitted commercial particulars. Quotation, acknowledgement, invoice and portal terms do not vary it unless authorised representatives expressly sign the identified variation. 4. Materials, compliance and workplace duties The Manufacturer must obtain materials allocated to it from approved sources, prevent substitution and contamination, and maintain traceability for [period]. It must hold the facility and manufacturing approvals allocated to it and promptly disclose an inspection, prohibition, failed test, suspected safety issue or disruption affecting Product. The Customer is responsible for the accuracy and lawful use of Customer-supplied design, formula, claims and marks except to the extent the Manufacturer expressly agreed to verify them. The Manufacturer is responsible for its process, workmanship, technical records and regulatory matters allocated to it. Schedule 1 must identify any product-specific approval, standard, consumer-information rule or market authorisation and the responsible party. Each party remains responsible for its duties under the Health and Safety at Work Act 2015. Where their work overlaps, they must consult, cooperate and coordinate so far as reasonably practicable. No provision transfers or excludes a statutory duty. 5. Inspection, remedy and recall The Customer may audit relevant production areas and records on reasonable notice without unreasonably disrupting operations. It may inspect before shipment and within [ten] Working Days after delivery. Inspection, payment or failure to inspect does not waive a latent Nonconformity or any right that cannot lawfully be excluded. The Manufacturer must segregate suspect Product. For a Nonconformity caused by its breach, it must, at the Customer's reasonable election, promptly rework, replace or refund the affected Product and bear reasonable documented retest, return and redelivery cost. The Customer bears equivalent cost caused by inaccurate Customer Property or an unauthorised Customer instruction. Each party must promptly notify the other of a suspected systemic defect, serious incident, regulator enquiry or recall request. They must cooperate on tracing, stop-supply, notice, correction and recall. Reasonable corrective cost is borne according to the extent each party's breach, negligence or supplied defective material caused the event, subject to mandatory law. 6. Delivery, title and risk The Manufacturer must deliver conforming Product with the documents and packaging in Schedule 2. Title passes [on full payment/on delivery]. Risk passes on delivery at the named destination unless Schedule 2 states an agreed delivery term and place. Customer Property remains the Customer's property. The Manufacturer must identify and segregate it, use it only for this agreement, exercise reasonable care and promptly report loss or damage. It must not create a security interest over Customer Property and must assist the Customer with any agreed PPSR protection. 7. Price, GST and payment Prices, permitted adjustment, GST treatment and milestones are in Schedule 2. The Manufacturer must provide taxable supply information where required. The Customer must pay an undisputed invoice within [twenty] Working Days and promptly explain a disputed amount. If both parties are in trade, the Product is acquired in trade and Schedule 2 expressly records agreement to contract out of identified provisions of the Consumer Guarantees Act 1993 or Fair Trading Act 1986, that agreement applies only to the extent contracting out is permitted and fair and reasonable. Otherwise all non-excludable rights remain. 8. Intellectual property and confidentiality Each party retains pre-existing intellectual property. The Customer owns the Product Dossier and Customer Property and licenses them to the Manufacturer during the term solely to perform accepted Production Orders. The Manufacturer must not sell overruns, seconds or Product and must de-brand or destroy rejected excess as reasonably directed. On full payment, the Manufacturer assigns to the Customer the rights it can assign in commissioned validation reports, bespoke tooling drawings and other Customer Deliverables identified in Schedule 3. The Manufacturer retains its general production methods and background know-how, subject to any licence expressly stated in Schedule 3 that is necessary to use a Customer Deliverable. Each party must protect the other's non-public technical and commercial information and disclose it only to bound people who need it or as law requires. 9. Term and cancellation This agreement starts on [date] and continues for [term]. Either party may end it on [ninety] days' notice, but an accepted Production Order continues unless agreed otherwise. A party may cancel for material breach when the contractual and statutory requirements for cancellation are met, including after [ten] Working Days to remedy where cure is possible. Immediate cancellation is permitted for fraud, insolvency, unlawful manufacture or an unremedied material product-safety risk. On ending, the Manufacturer must stop unauthorised production, return Customer Property, deliver paid conforming work in progress and provide traceability and validation records. The Customer must pay for conforming accepted work. Accrued payment, quality remedies, recall, confidentiality and intellectual-property rights survive. 10. General The Manufacturer may not subcontract a critical operation without written consent and remains responsible for approved subcontractors. Changes must be signed by authorised representatives. Notices must be delivered by hand, tracked post or email and are effective on proven receipt. Neither party may assign this agreement without consent except to a successor to substantially all the relevant business that assumes it. New Zealand law governs, and New Zealand courts have jurisdiction. SCHEDULE 1 PRODUCT, TRANSFER AND VALIDATION [Product; Product Dossier; trial and validation plan; approved sources; Lot records; release tests; shelf life; packaging/labels; approvals and responsible party]. SCHEDULE 2 ORDERS, DELIVERY AND PRICE [Forecast/minimum; lead time; quantities; NZD prices; GST; delivery; documents; invoicing/payment; any specific and fair trade-only contracting out]. SCHEDULE 3 CUSTOMER PROPERTY AND RIGHTS [Materials; tooling; samples; marks; Customer Deliverables; background-IP licence if any; PPSR/return arrangements]. SIGNATURES For the Customer: [authorised signatory, position, signature and date]. For the Manufacturer: [authorised signatory, position, signature and date]. Witness if used: [name, address, signature and date].

Licensed under CC BY 4.0. Attribution is required when you publish or redistribute this Template or an adapted version to the public. Attribution is not required merely because you use or adapt the Template for your own business or legal purposes, including preparing, negotiating, signing, or exchanging an agreement with a counterparty. License details.

More templates for New Zealand